Panels fail in ways that are easy to miss until they are not. Breakers that will not stay set, a burning smell near the enclosure, rust down the back from a leak nobody noticed, or a Federal Pacific label. We repair what can be repaired, and when the panel itself is the fault we run a full load calculation before quoting so the replacement is sized to your house rather than to a round number. Service upgrades from 100 amp to 200 amp get coordinated with Tacoma Power for the meter and the drop, and we book the inspection. If you have searched for electrical panel repair near me and gotten a phone quote without anyone looking at the panel, that quote is a guess.
Knob and tube, cloth conductors and aluminum branch circuits all turn up regularly in Tacoma, particularly north of Division. A full rewire sounds catastrophic and usually is not. We work circuit by circuit, fish cable through existing cavities wherever the framing allows it, and sequence the work so you can keep living in the house while it happens. The whole job is permitted through Tacoma Power and inspected in stages. Homeowners looking for home rewiring near me are often being quoted for a gut renovation when what they need is a staged rewire, and those are very different numbers.
Level 2 charging for Tesla, Ford, Rivian, Hyundai and anything running a J1772 or NACS connector. The order matters here. We check whether your existing service can carry the load before we sell you anything, because a 100 amp panel in a South Tacoma rambler often cannot take a 48 amp charger without a service upgrade first. You hear that at the estimate rather than after the truck is unloaded. Then we pull the permit, run the circuit, mount the unit and stay on it through inspection. As EV charger installers we are looking at your whole electrical system, not just the wall where you want the box.
Rough-in through trim-out on custom homes, ADUs, detached garages and shops. We read the plans, coordinate with your general contractor and the other trades, and set boxes where the drywall crew will not have to guess. On Tacoma builds we handle the Tacoma Power permit track from the start, including plan review submission when the service is large enough to need it. New construction wiring is mostly a scheduling problem, and being late for rough-in holds up four other trades behind you.
Burning smell, sparking outlet, scorch marks around a plug, a breaker that will not reset, half the house dark with the neighbors still lit. Call us. We answer around the clock and our trucks are stocked well enough that most emergency calls finish on the first visit. Being based in Puyallup rather than Seattle is the whole point on an emergency call, because a crew coming down I-5 in afternoon traffic is not a fast crew.
Dead outlets, warm faceplates, scorching around the slots, or a two-prong receptacle with nowhere to land a ground wire. We replace what has failed and add outlets where you actually need them, with GFCI protection in kitchens, bathrooms, garages, crawlspaces and anywhere outdoors. Older Tacoma houses tend to have one outlet per wall and no ground. Both of those are fixable.
Ungrounded two-prong outlets are standard in Tacoma houses built before the mid 1960s. Swapping in a three-prong receptacle without running a ground does not fix anything. It hides the problem behind a plug that now fits, and it makes the house look safer to the next buyer than it is. We run a real ground where the cavity allows it, install GFCI protection where a ground wire is not practical, and label the outlet the way code requires.
A switch that buzzes, feels warm, or has to be held in a particular position has a loose connection or the wrong load behind it. We replace failing switches, wire three-way and four-way circuits so a hallway or a staircase works from both ends, and match dimmers to your LED fixtures so the lights stop flickering. We also hardwire and interconnect smoke and carbon monoxide alarms, which Washington requires in bedrooms, hallways and outside sleeping areas. Battery units stuck to a ceiling usually do not satisfy that requirement.
Recessed cans, under-cabinet strips, outdoor and landscape lighting, and full fixture replacement. Layout is the part people skip and it is the part that decides whether you like the room afterward. Cans in the wrong place put a shadow across the exact stretch of counter you cook on. We plan it with you before anyone opens a ladder.
Hanging a fan is not the same as hanging a light. The box has to carry the static weight plus the wobble, and most of the boxes we open in older Tacoma homes were never rated for it. We install fan-rated boxes, run the wiring for separate light and fan control, and mount units on sloped and vaulted ceilings.
Breakers trip for a reason. Sometimes it is a space heater and a microwave sharing one kitchen circuit. Sometimes it is a short inside a wall. We find out which before replacing anything, then fit correctly sized breakers and add AFCI or GFCI protection where the current code cycle requires it. Repeatedly resetting a breaker without finding the cause is how a nuisance becomes a fire.
Hot tubs, saunas, well pumps, workshop equipment, window air conditioners, anything with a motor in it. All of that runs better and lasts longer on its own circuit. We size the conductor for the load and for the length of the run, so you are not losing voltage halfway across the yard to a detached garage.
Kitchens and bathrooms need considerably more circuits than they did when your house was built, and current code is specific about it. Basement conversions and ADU builds usually need their own subpanel. We work around finished surfaces, fish wire instead of opening walls wherever that is possible, and sequence around your other trades so nobody is standing around waiting on us.
